New steel garage door on a suburban home exterior with driveway and warm afternoon light.

How Much Does A Garage Door Cost?

A new garage door costs $700 to $4,500 installed in the United States, and most homeowners land somewhere between $1,200 and $2,800 for a standard steel door with professional installation. A basic single-car steel door sits at the bottom of that range, while a double-width wood or custom door with a smart opener sits at the top. The spread is wide because “a garage door” covers two very different jobs: swapping a plain steel panel for a similar one, and ordering a wide, insulated, carriage-house door with windows and a new opener.

That range is not one source’s guess. Cost guides published in 2026 disagree with each other by hundreds of dollars on the same door, and this article says where they disagree instead of hiding it. This Old House, using Homewyse data, puts the average standard installation at about $1,400, with most homeowners paying $1,151 to $1,869. Installer-written guides put the typical job higher, around $1,500 to $3,800 for a professionally installed replacement. The honest way to read those numbers is that the lower figure reflects a basic single door, while the higher ones include double doors, insulation and better hardware. Budget with the range that matches the door you actually want, not the national average.

Garage Door Cost At A Glance

If you want one number before the detail, this table is it. Prices are installed totals, door plus labor, for the most common configurations in the US.

Door Typical Installed Cost
Basic single steel, 8×7 or 9×7 ft $700–$2,200
Mid-range single steel, insulated $1,200–$2,500
Standard double steel, 16×7 ft $1,200–$4,500
Mid-range double steel, insulated $1,800–$3,800
Wood or custom double door $3,500–$10,000+
Garage door opener, added to the job $350–$850

Three things decide where you land inside those ranges: the size of the opening, the material of the door, and the features you add. Everything else — labor rates in your city, permits, wind ratings — moves the number by hundreds, not thousands, unless you are resizing the opening itself.

How Much Does A Garage Door Cost By Size?

Size is the first fork in the road, and it matters more than most people expect. A double door is not simply twice the price of a single. It needs a wider track, heavier springs rated for more weight, and reinforced panels to span 16 feet without sagging, so the premium usually runs 60 to 100 percent higher, not 200 percent.

A single-car door, 8 or 9 feet wide by 7 feet tall, costs $700 to $2,200 installed. The 8-foot width shows up in older homes; the 9-foot width is the modern standard, and it is the size most new homes use. An oversized single at 10 feet wide, or a tall single at 8 feet high for a pickup truck, runs $1,200 to $2,800 installed. Going from 7 feet tall to 8 feet tall adds roughly $150 to $400 to the same door.

A double-car door, 16 feet wide by 7 feet tall, costs $1,200 to $4,500 installed. That is the standard two-car opening, and it is the most common configuration in the country. A tall double at 16 by 8 feet runs $2,000 to $5,000, and a wide double at 18 by 7 feet runs $2,200 to $5,500. A three-car garage, with openings totaling 30 to 36 feet, runs $1,400 to $7,200 depending on whether it uses one double plus one single or three separate singles.

Two singles versus one double is a real choice. Many two-car garages have two separate single doors side by side instead of one wide door. The single wide door is usually the cheaper install, because you pay for one track and one opener instead of two of everything. But two singles let you open only one bay, and if one door breaks, the other still works. If your garage currently has two singles and you want to switch to one wide door, budget for header and framing work on top of the door itself — that is structural work, and it is the kind of line item that turns a $1,500 quote into a $4,000 one.

Custom sizes carry a real premium. Any opening outside the standard 8×7, 9×7 or 16×7 sizes usually means a door built to order. Guides put that upcharge at $500 to $2,000, or roughly 20 to 40 percent over the base material cost. Measure the framed opening, not the old door slab, before you request quotes, and check the side room for the tracks and the headroom above the opening for the springs.

Garage Door Cost By Material

Material is the single biggest driver of garage door price after size, and it is the choice that shapes the next 15 to 30 years of maintenance. Steel dominates the market because it is cheap, strong and low-maintenance. Wood wins on looks and loses on upkeep. The rest sit in between.

Steel Garage Doors

Steel costs $600 to $4,000 or more for the door alone, and $1,500 to $4,500 installed for a double. It is the default for most homes, and for good reason: it is durable, it does not warp or rot, and it comes in every style from plain flush panels to wood-grain embossed carriage house designs. The price depends on the layers. A single-layer, non-insulated steel door is the cheapest option at $500 to $1,200 installed for a single, but it dents visibly and offers almost no sound or heat barrier. A double-layer door with polystyrene insulation runs $900 to $2,000 for a single. A triple-layer door with injected polyurethane foam runs $1,200 to $2,800 for a single and $2,000 to $4,000 or more for a double, and it is quieter, stiffer and better insulated. If the garage shares a wall with a bedroom, spend the extra money on insulation. If it is detached and unheated, the bare steel door is a legitimate choice.

Tip: check the steel gauge before you compare two quotes. A thinner 24-gauge panel dents more easily than a thicker panel, and two doors both labeled “steel, insulated” can differ by hundreds of dollars in actual quality. Get the gauge and the R-value in writing.

Modern insulated steel garage door in light gray with raised panels on a brick home

Wood Garage Doors

Wood costs $1,500 to $8,000 or more for the door alone, and $3,500 to $9,000 installed for a double. It is the most expensive common material and the most beautiful one. Cedar is the usual choice because it resists rot better than fir or hemlock, and a custom carriage-house wood door can pass $10,000 installed. The sticker price undersells the total cost, though. A wood door needs refinishing every 2 to 5 years, depending on sun and rain, and skipping that turns a $3,000 door into a peeling one within a decade. Wood suits historic homes, carriage-house styles and owners who genuinely enjoy the upkeep. If you love the look but not the maintenance, read the composite section next.

Wood carriage house garage door with black decorative hardware and arched windows

Aluminum Garage Doors

Aluminum costs $900 to $5,000 or more for the door alone, and $2,000 to $8,000 installed for a double. Standard aluminum doors sit at the lower end, while full-view aluminum frames with glass panels sit at the top. Aluminum is light and it will not rust, which makes it the natural choice for coastal homes and humid climates. The trade-off is that it dents more easily than steel and usually carries a lower wind-load rating unless it is reinforced. A full-view glass door in an aluminum frame is a striking modern look, but it is also the priciest way to fill an opening, and it insulates poorly compared with a foam-filled steel door.

Fiberglass Garage Doors

Fiberglass costs $1,200 to $6,000 for the door alone, and $2,800 to $7,000 installed for a double. It resists moisture, salt air and denting, which is why it shows up most often in humid and coastal areas. It can mimic wood grain convincingly, and it needs very little maintenance. The downsides are fewer style options than steel or wood, and a tendency to fade or crack in extreme cold. For a coastal home where steel would corrode and wood would rot, fiberglass is often the smartest money in this list.

Vinyl And Wood-Composite Garage Doors

Vinyl doors run about $800 to $2,500 installed, making them one of the cheapest options overall. Vinyl resists dents and rust, never needs painting, and suits families with kids and basketballs in the driveway. The catch is a short style list and colors that can fade in strong sun. Wood-composite doors, sometimes called faux wood, cost $1,200 to $4,500 for the door alone and $2,500 to $5,500 installed for a double. They pair a steel structure with an embossed wood-grain overlay, so they look like wood without the refinishing schedule. For most homeowners who want the carriage-house look on a realistic budget, composite is the compromise that actually holds up.

Material Installed Cost, Double Door Maintenance Best For
Steel $1,500–$4,500 Low Most homes, best value
Wood $3,500–$9,000 High Historic homes, curb appeal
Wood-composite $2,500–$5,500 Low to medium Wood look without the upkeep
Aluminum $2,000–$8,000 Low Coastal homes, modern glass looks
Fiberglass $2,800–$7,000 Low Humid and coastal climates
Vinyl $800–$2,500 Low Budget, dent resistance

Garage Door Cost By Style And Type

Style is the visual design of the door, and it adds cost on top of the material. A plain flush-panel door is the baseline. Everything decorative costs extra.

Sectional doors are the standard. They are made of horizontal panels that slide up along ceiling-mounted tracks, and they are what almost every cost figure in this article assumes. A standard raised-panel sectional is the most popular style in the country and adds only $100 to $300 over a flush panel.

Roll-up doors cost $1,500 to $2,400 on average for the door. They use horizontal steel sheets that roll onto a drum above the opening, and they suit garages with high ceilings or tight headroom. They are more common in commercial buildings than in homes.

Carriage-house doors add $300 to $1,200 over a basic door. They look like old swing-out barn doors, with decorative hinges, handles and straps, but they still open as a sectional door. The style is one of the most popular upgrades at this price point, and it is where a mid-range steel door starts to look custom.

Contemporary and modern doors add $200 to $800. Clean horizontal lines, minimal hardware, and long windows suit modern homes. Full-view glass doors, with aluminum frames and large glass panels, add $800 to $3,500 and are the most expensive style short of custom wood.

Tilt-up doors, a single solid panel that lifts outward, average $1,100 to $1,250 for the door. They need clearance in front of the garage to swing out, which is why they are less common on short driveways.

How Much Insulation Adds To The Price?

Insulation is worth pricing as its own line, because it is the upgrade most often bundled silently into a quote. An insulated door is quieter, stiffer, and keeps an attached garage from bleeding heat into the wall it shares with the house.

Insulation R-Value Price Premium
None, single layer R-0 Baseline
Polystyrene board R-6 to R-9 +$150–$350
Polyurethane foam, injected R-12 to R-18 +$300–$700
High-R premium panels R-18+ +$500–$1,200

A door rated below R-9 barely counts as insulated, and the jump from polystyrene to polyurethane is the one worth paying for if the garage is attached or used as a workspace. One guide estimates an insulated R-12 to R-18 door saves roughly $60 to $200 a year on energy bills for an attached garage, which means the upgrade can pay for itself over several winters. For a detached garage you rarely heat, skip the insulation and keep the money.

Garage Door Opener Costs

The opener is a separate purchase from the door, and it is the line item most often missing from a first quote. If your opener is more than 10 to 15 years old, replace it with the door — you are paying for the same service call either way, and a heavier insulated door can strain an old motor.

Opener Type Installed Cost, Added To A Door Job
Chain-drive, basic $350–$550
Belt-drive, quieter $400–$650
Screw-drive $380–$600
Direct-drive, very quiet $450–$750
Smart Wi-Fi opener $450–$850

Chain drives are reliable and cheap, but noisy — a real problem if a bedroom sits above the garage. Belt drives are the usual recommendation for attached garages because they run noticeably quieter. Smart openers add phone control, alerts when the door is left open, and battery backup on the better models. Adding an opener to a door that is currently manual, or upgrading to a smart model, adds roughly $200 to $1,300 to a project depending on horsepower and features. A wall-mount jackshaft opener, which frees up ceiling space, runs $400 to $600 for the unit before installation.

Labor And Installation Costs

Labor is the line homeowners underestimate most, because they focus on the door and forget that someone has to hang it. A straightforward replacement takes 3 to 6 hours with a two-person crew; a double door with a new opener and old-door removal runs 4 to 8 hours.

Service Typical Labor Cost
Basic door replacement, door swap only $250–$400
Full install with new tracks and hardware $350–$600
New opener installation, same visit +$200–$350
Old door removal and disposal +$50–$200
Framing modification, non-standard opening +$300–$800
Permit, where required $50–$250

Most guides put straight-swap labor at $200 to $500 per door, with the exact figure following local wages — installers in high-cost metros charge near the top, and small-town installers near the bottom. A full installation covers removing and hauling away the old door, mounting new tracks and hardware sized to the new door’s weight, setting and tensioning the springs, and testing the opener so the door reverses correctly on contact. The springs are the single most dangerous part of the job, and the reason this is not a DIY project for most homeowners. A like-for-like door swap usually needs no permit. Resizing the opening or converting two singles into one double does, and in Florida a wind-rated door in a Wind-Borne Debris Region needs an inspector to verify its approval.

Tip: when you compare quotes, confirm whether each one is “door only” or “door installed with hardware,” and whether haul-away is included or a surprise line item at the end. Three quotes on the identical spec — same brand and line, same R-value, same opener — is the only way to see a real price spread. A 20 to 30 percent gap on paper-identical scope is normal in this trade.

Extras That Add To The Bill

Small choices stack up fast on a garage door, and they are where a $1,800 quote becomes a $2,800 invoice. Price them before you fall in love with them.

Windows add $150 to $600 for a single row across the top panels, and $200 to $800 for larger or insulated glass. They bring natural light into the garage and break up a big blank door, but they cost more to insulate around and they reduce privacy if the garage faces the street.

Decorative hardware adds $50 to $400. Carriage-house handles, hinges and straps are the classic example. They are cheap individually and surprisingly visible from the curb, which is why installers upsell them.

Premium colors and finishes add $200 to $600. Custom paint colors, faux wood grain and wood embossing all sit in this band. A standard white, almond or brown door costs nothing extra.

Wind and impact ratings add $300 to $1,500. In hurricane-prone states like Florida and coastal Texas, wind-rated doors are often required by local building code. They are built to withstand 110 to 150 mph winds and higher, and the testing and reinforcement behind that rating is what you are paying for.

Smart features add $200 to $500 on top of a standard opener. Wi-Fi connectivity, battery backup, a camera and timer-to-close automation each add their own slice. Battery backup alone runs $150 to $300 and earns its keep in areas with frequent power cuts.

Double garage door on a two-car garage with stone facade and paved driveway

What Moves The Price Most?

Where you live moves the labor half of the quote. The door itself costs about the same wholesale in Tampa as in Tacoma, but the installer does not. For the same mid-range double steel door, guides put the installed cost at roughly $2,000 to $4,000 in the Southeast and South, $2,200 to $4,200 in the Midwest and Mountain West, and $2,800 to $5,500 on the West Coast and in the Northeast. Big metro installs commonly run 30 to 50 percent higher than small-town ones.

Custom sizing is the quiet budget-killer. A non-standard width or height adds $500 to $2,000, and it also adds lead time, since the factory builds the door to order. Measure the opening before you shop, not after you have picked a door.

Climate and code add their own lines. Coastal homes pay for rust-resistant hardware and wind ratings. Cold-climate homes pay for insulation. Washington’s energy code sets U-factor requirements for glazed garage doors, and Florida’s building code sets wind-load rules — both can force a more expensive door than the national guides assume.

Timing matters less than people think, but it matters. Late fall and winter are slower seasons for installers in cold climates, and some offer discounts then. Same-day or emergency installation adds $100 to $300. A scheduled job in the off-season is the cheapest way to buy the same door.

How To Save Money On A Garage Door?

You do not need the cheapest door to get a fair price. You need to cut the costs that buy nothing and keep the ones that do.

  • Get three quotes on the identical spec. Same brand, same line, same R-value, same opener. A 10 to 20 percent saving against a single quote is common, and the spread shows up only when the scope matches.
  • Keep the existing opener if it works. Reusing a good opener saves $350 to $850 against replacing both at once. Replace it only if it is over 10 to 15 years old or cannot lift the new, heavier door.
  • Stay with a standard size. Stock sizes ship fast and cost less than custom orders. A standard 9×7 or 16×7 door is the cheapest way to fill a standard opening.
  • Skip decorative extras on a tight budget. Windows, carriage hardware and premium colors save $300 to $1,000 on a double door without changing how the door works.
  • Choose mid-tier over premium where it counts. An insulated steel door gives you most of the performance of a wood door at a third of the price, and it needs almost no maintenance.
  • Ask about manufacturer promotions. Clopay, Wayne Dalton and other brands run seasonal rebates through authorized dealers, and installers rarely volunteer them.

Is A New Garage Door Worth It?

A garage door is one of the few home improvements where the resale math is genuinely strong. Remodeling Magazine’s Cost vs. Value report has ranked garage door replacement the top-recouping project in the country for most of the last decade. The figures differ by year and by source, so read them carefully: This Old House puts the return at 85 to 95 percent of the project cost, while the older Cost vs. Value framing cited by some guides puts a midrange door at around $4,300 installed adding back roughly $8,300 at resale, close to 194 percent. The newer, lower figure is the safer one to plan around, and even at 85 to 95 percent it beats almost every other exterior project.

The reason is simple. A garage door is the single largest moving part on most home facades, and it is the first thing a buyer sees pulling up. A dented, faded door drags down curb appeal more than its condition deserves, and a clean new one fixes that for a few thousand dollars instead of the tens of thousands a full exterior renovation would cost. If you are selling within one to three years, a mid-range door is one of the clearest “do it” improvements there is. If you are staying long-term, buy the door you actually want to live with — insulation, quiet operation and a smart opener pay you back in daily comfort, not just at resale. This Old House’s full cost guide, How Much Does a Garage Door Cost?, breaks down the same numbers by type and material if you want a second set of figures before you call an installer.

Repair Or Replace: The Quick Rule

Not every tired garage door needs replacing. A single broken spring costs $150 to $350 to replace, a panel $200 to $500, rollers and track work $100 to $300, and a sensor alignment $75 to $150. Replace the door when the repair bill passes 60 to 70 percent of a new installation, when several parts fail at once, or when the door is over 15 to 20 years old and lacks modern safety features. A door that is bent, warped, rotting or no longer sealing out weather is a replacement, not a repair. And if your opener was installed before the early 1990s, check that it has photoelectric safety sensors no more than six inches off the floor — entrapment protection has been a federal requirement since then, and a missing sensor is a safety problem, not a cosmetic one.

Frequently Asked Questions

How Much Does A Single Garage Door Cost Compared To A Double?

A single-car door, 8 or 9 feet wide, costs $700 to $2,200 installed, while a standard double door, 16 feet wide, costs $1,200 to $4,500 installed. The double is not twice the price of the single, because one wide door needs only one track and one opener, but it does need heavier springs and reinforced panels, so expect the double to run roughly 60 to 100 percent more than a single in the same material.

What Is The Cheapest Garage Door Material?

Steel is the cheapest door to buy, and vinyl is the cheapest installed option overall at roughly $800 to $2,500. A basic single-layer steel door is the lowest-cost standard choice for most homes, starting around $500 to $1,200 installed for a single. Insulated steel costs a few hundred more and is the better buy for any attached garage.

Does The Price Include The Garage Door Opener?

Usually not, or only a basic one. Most installed-price figures cover the door, tracks, hardware and labor. A new opener adds $350 to $850 depending on the drive type, with chain drives cheapest and smart Wi-Fi openers dearest. Always ask whether the quote includes the opener, removal of the old door, and a permit, so you are comparing like with like.

Do I Need A Permit To Replace A Garage Door?

Usually no, for a like-for-like swap of the same size. A permit, typically $50 to $250, becomes necessary when you resize the opening, convert two single doors into one double, or install a wind-rated door in a hurricane zone that needs inspection. Check with your city before you schedule the work, not after.

How Long Does Garage Door Installation Take?

A straightforward single-door replacement takes 3 to 5 hours. A double door, or a job that includes a new opener, spring system and old-door removal, usually runs 4 to 8 hours. Custom or oversized doors can take a full day. Get the timeline in writing with the quote, so a half-day job does not quietly become a two-day one.

Conclusion

A garage door is a big, visible purchase, but it does not have to be a confusing one. Size and material set the price, insulation and the opener add their own lines, and labor follows your local market. Get three quotes on the same spec, keep the opener if it still works, and spend the money on the door you will see every day. If the garage sits under a bedroom or shares a wall with the house, the insulated steel door in the middle of the range is the choice most homeowners end up happiest with. And if the garage itself needs sorting once the new door is in, our garage organization ideas show how to make the space behind it work as well as the door in front of it. A new door also changes the front of the house, so it is worth thinking about it alongside the rest of the exterior — our house plans with garage show how the garage and the facade are designed together, and our how much does a fence cost guide prices the other big curb-appeal project the same way.

Garage door with a row of windows across the top panels letting in natural light

Leave a Comment

Your email address will not be published. Required fields are marked *

Save to list